Keurig coffee maker blinking lights

Step 2: Check the Drip Stop Lever. The drip stop lever is vital to managing coffee flow from the brew basket to the carafe. Check the lever's position. It can block the brewing process and cause the brew light to flash if half closed or midway. Allow coffee to flow into the carafe by fully opening the drip stop lever.

It can be frustrating when your Keurig lights are not blinking as they should, but with a few simple steps, you may get your coffee maker back up and strolling smoothly. 1. Check the power source: Ensure that your Keurig coffee maker is properly plugged into a functioning power outlet. Sometimes, a loose connection or power surge can cause the ...The descaling process goes as follows: Add a bottle of Keurig descale solution and water to the tank. Press and hold the 8oz and 12oz buttons together for 3 seconds to activate Descale Mode. When the BREW button starts flashing, press it to dispense the solution. Once complete, throw the liquid into the sink.1-4 of 4 Answers. Clean the puncture needle on top of the lid that punctures the k-cup it’s probably plugged. Lift the lid and take the 4 screw out, this allows you to get that top plate down and exposes the top of the needle and the rubber hose then you can take it apart and clean it. Just be careful it’s sharp.STEP 2: Descaling the Brewer. To activate Descale Mode, plug in your Keurig but keep it turned off. Then, press the ' 8oz' and ' 12oz' buttons at the same time for 3 seconds. When the lights blink, press the 'K' button to initiate the descaling process. When it's done, throw away the hot liquid in the sink.The Keurig K-Cafe coffee maker has been a game-changer for many coffee enthusiasts, offering the convenience of brewing coffee, lattes, and cappuccinos with just a touch of a button. However, like any electronic device, it might encounter issues, such as the frother lights flashing unexpectedly.Run a water-only brew cycle to flush any remaining debris from the machine. 3. Issue With Water Filter. If your Keurig’s “add water” light isn’t working right, the water filter might be the culprit. A dirty or clogged filter can mess with the water flow, causing the light to flash or not come on at all.The issue may be with the coffee maker itself if the coffee maker is plugged in and the water reservoir is filled. The light is flashing and there’s no coffee brewing, unplug the coffee maker and contact Keurig customer service for further troubleshooting. Keurig K-Slim Descale Light Stays On

A safe place to talk about the Keurig K-Cup Coffee system. ... Automatic Tea Maker with Coffee Machine ... I've had this light for 5+ years and it's been through all kinds of shenanigans - submersed in hot CIP chemicals for hours and came out with the light still on. Impressive! It's made by Hictech. Any help appreciated!First, make sure that the coffee maker is properly plugged in and that the outlet is working. Next, check to see if the coffee maker's light is turned on. If it is, try to turn it off by pressing the power button. If the light won 't turn off, you may need to reset the coffee maker. To do this, unplug the coffee maker and then plug it back in. By addressing these potential causes, you can improve the taste of your Keurig coffee. If the problem persists, you may want to contact Keurig customer support or take the machine to a professional for repair. 10. My coffee contains grounds. If your Keurig coffee contains grounds, there are a few potential causes and solutions you can try. How To find Low Water Sensor & clean vent tube. Keurig K-Duo Add Water Light will not stop flashing. on Keurig K-Duo Essentials Coffee Maker, with Single S...Nov 24, 2023 · The Keurig K-Cafe coffee maker has been a game-changer for many coffee enthusiasts, offering the convenience of brewing coffee, lattes, and cappuccinos with just a touch of a button. However, like any electronic device, it might encounter issues, such as the frother lights flashing unexpectedly. If you’ve encountered this problem, fear not! Follow these simple steps to do it in 10 minutes: 1- Remove the pod holder from the brewer. To remove the pod holder, lift the handle, grasp the top of the pod holder with one hand, and push it up. 2- Take out the funnel. Detach the funnel by pushing the sides of the pod holder. 3- Clean the tubes and Pod holder.Nov 23, 2023 · 1) Unplug the machine, and drain any water left in the reservoir. 2) Take the water filter and coffee pods out of the machine. 3) Place a coffee mug underneath the coffee outlet. 4) Pour the Keurig descaling solution and filtered water into the water reservoir. Use a 1:1 ratio of Keurig descaling solution and water. Contents show 1 Why are All the Lights on Keurig Coffee Maker Illuminated? 2 Quick Fixes for Keurig All Lights on 2.1 Check the Power Source and How It's Connected 2.2 Turn the Keurig Machine Back on 2.3 Check and Change the Location of the Water Reservoir 2.4 Make Sure There's Enough Water 2.5 Check […]

Keurig coffee makers are some of the most popular coffee makers in the United States with some stats showing that roughly 1 in 4 US households owns a Keurig. ... To turn the device on, press the power button. A green light should appear when the machine turns on. This green light will turn red once the brewer is starting to heat the water.Here's how you can factory reset Keurig K Supreme. Press and hold the two arrow buttons for three seconds. "Setting Menu" will appear on the screen, press the right arrow button to proceed. Press the right arrow button seven times until the "Factory Reset" appears on the screen. Press the "K Button" and press the right arrow ...A red light flashing indicates that your Keurig coffee maker has accumulated dirt and needs a descaling. To fix this issue, you must descale the machine with the cleaning solution. Sometimes you may notice a blue light flashing when the water reservoir is low; refill the water to fix that.The Power Button Is Not Pushed To The Turn On Keurig K900 Position. The Keurig k900 has a power-on button or an ON/OFF switch on it. The switch is located on top of the machine. For a Plus, the 2.0 model that has a touchscreen, the power button is located right at the bottom right the corner of the screen of your machine.The same principle applies when cleaning the coffee maker. Using water that's loaded with minerals like calcium and magnesium to clean the Keurig only accelerates the buildup of residue and ...

Fedex on mckinley.

Hold down the power button. Press the buttons for the cup sizes starting from the smallest to the largest. Do steps 2 to 4 two more times. Open and close the lid one last time, and it should work properly now. After resetting, you might be able to make only a couple of cups before the lights come on again. The issue may be with the coffee maker itself if the coffee maker is plugged in and the water reservoir is filled. The light is flashing and there’s no coffee brewing, unplug the coffee maker and contact Keurig customer service for further troubleshooting. Keurig K-Slim Descale Light Stays On However, if the lights are flashing, you should perform a manual cleaning or descaling cycle. A cleaning or descaling cycle only takes a few minutes but your espresso may have more flavor afterwards. As a general rule of thumb, you should perform a manual cleaning or descaling cycle after making 200 espressos, or every six months, whichever ...Step on is to do the 3 cleansing brews but I'm at a roadblock. All the lights are on steady and not selectable. There's water in the tank, filled to just below the max line. The next step is to lift and close the handle. Done. Lights still steady, not flashing meaning it's ready for a brew. Again this is right out the box so it's not ...Go to the menu and scroll to programming options. Both auto off and on/off should be saying “OFF.”. If not, change it to off. 7. Blue light flashing in the water reservoir: The water level is probably low. Fill up your water reservoir. If it indicates ‘PRIME,’ refer to the above-mentioned problem and solution.If you love your Keurig coffee maker, encountering issues can start your day off wrong. One common issue is when all the lights start flashing. Don't worry. We'll show you easy steps to fix this. Understanding Why All Lights Are Flashing on Keurig

Yes, espresso machines and other coffee makers can be fire hazards. That's because coffee machines have heating elements that can overheat and electrical connectors that can erode. Those problems can lead to fires. Do Coffee Makers Have Sensors? Yes, some coffee maker models have sensors. These include temperature and water sensors.Blue lights wouldn’t come on. I hit the glass pot button like 20+ times. Turned it on and off and pressed the glass pot button again and the blue lights came on like normal and now I can brew with my glass pot again. Note: I have the double brew station. One for a pot and the other for a cup. I cleaned it with the Keurig Descale Solution and ...A safe place to talk about the Keurig K-Cup Coffee system. ... The machine was off but plugged in, and the "cold" button to make cold foam was blinking light and beeping in a random pattern. Got up to see what it was, turned the keurig on, and the beeping still continues. ... out of warranty will give you 20% off then she offered free shipping ...Keurig K-Duo Essentials Light Flashing But Not Brewing. If you are one of the many people who have had trouble with their Keurig K-Duo essentials light flashing but not brewing, there may be a few reasons for that. One reason could be that the coffee machine is not properly configured to use two different types of coffee grounds - blue and black.Step 1. You will have to press the machine button for 3 seconds to turn it off. Step 2. Wait for around 20 to 30 minutes for the machine to cool down. Step 3. The machine might continue to blink orange light even after you give it adequate time to cool down. In that case, your machine is probably in descaling mode.Yes, espresso machines and other coffee makers can be fire hazards. That’s because coffee machines have heating elements that can overheat and electrical connectors that can erode. Those problems can lead to fires. Do Coffee Makers Have Sensors? Yes, some coffee maker models have sensors. These include temperature and water sensors.The descaling process goes as follows: Add a bottle of Keurig descale solution and water to the tank. Press and hold the 8oz and 12oz buttons together for 3 seconds to activate Descale Mode. When the BREW button starts flashing, press it to dispense the solution. Once complete, throw the liquid into the sink.Place a large coffee mug on the stand. Lift the Keurig handle up and then back down. Select the 10oz button (the largest one) and press it to start the process. Pour out the contents and repeat the process until the "add more water" light comes on. Allow your Keurig to sit (power on) for 30 minutes.

The Keurig K-Cafe coffee maker has been a game-changer for many coffee enthusiasts, offering the convenience of brewing coffee, lattes, and cappuccinos with just a touch of a button. However, like any electronic device, it might encounter issues, such as the frother lights flashing unexpectedly.

Keurig Milk Frother Problems. Keurig is one of the world’s leading brands that makes the best performing kitchen appliances on the market. The Keurig brand has a variety of appliances that are exceptionally good in terms of quality, durability and features. That’s why you may want a Keurig milk frother to make delectable beverages. Whether ...If your Keurig K Compact coffee maker's lights are flashing, it could be due to a few different reasons. The first thing you should check is whether or not the water reservoir is empty. If it is, simply refill it and the lights should stop flashing. If the water reservoir isn't the issue, then it could be a problem with the coffee maker's ...In college, when I worked part-time as a barista at a local coffee shop, I would often serve the same customers day in and day out. To the point that, before they’d even say anythi...Keurig K-Elite Light Flashing But Not Brewing. If your Keurig K-Elite coffee maker is flashing but not brewing, make sure that the coffee maker is plugged in and that the water reservoir is full. If the coffee maker still isn't brewing, try running a cleaning cycle. If the problem persists, call Keurig customer service for assistance.The descaling process goes as follows: Add a bottle of Keurig descale solution and water to the tank. Press and hold the 8oz and 12oz buttons together for 3 seconds to activate Descale Mode. When the BREW button starts flashing, press it to dispense the solution. Once complete, throw the liquid into the sink.new Keurig® coffee maker Use & Care Guide. 12 8 10 6 AUTO 12:00 PM STRONG H M The water reservoir can be positioned to the right, left, or ... 8 button — the brew indicator light will blink. Press the brew button to start the cleansing brew. The cleansing brew will begin once the coffee maker is heated.Coffee Maker Exterior Keep your Keurig® coffee maker looking its best by cleaning the exterior from time to time. Just clean with a damp, soapy, lint-free, non-abrasive cloth. Never immerse the coffee maker in water or other liquids. Drip Tray The drip tray can hold up to 237 ml/8 oz of overflow and should be emptied and cleaned occasionally.Solution: Press The Power Button. To activate your Keurig K-Elite, simply press the power button once, located on the front upper part of the machine. Another method you can try is to press and hold the power button for 10 seconds until the green power light illuminates.Apr 22, 2022 · Turn off your brewer and unplug it from its power source. Allow 30 seconds for your brewer to cool down. While holding down both buttons on top of your brewer, plug in your brewer and turn it back on. Continue holding down both buttons until you hear a single beep or see a small green light (depending on the model) You have now successfully ... DESCALE light turns solid. When brew button begins flashing, press the brew button to start the cleansing rinse brew. Pour the hot liquid into the sink. Repeat the cleansing rinse process until the ADD WATER light illuminates. STEP 2: Rest & Rinse Empty the water reservoir and refill to the MAX fill line with fresh water. STEP 3: Fresh Water Rinse

Magic matt 70s on 7.

Centennial rewards.

4 Keurig K-express Essentials Flashing Lights Issue. 4.1 Troubleshooting The Water Filter And Reservoir For Faults Or Misalignment; 4.2 Resetting The Coffee Maker Manually To Fix The Flashing Lights Problem; 5 Keurig K-express Essentials Power Issues. 5.1 Troubleshooting Steps For Keurig K-express Essentials Not Powering On All you need to do is follow these simple steps. 1) Fill the water reservoir with cold filtered water and put it back in the machine. 2) Press the button for your desired cup size and brew strength. 3) Put your favorite coffee grounds into the filter basket, then press down on the lid until you hear a click sound.Fill a pitcher with plain white vinegar. Place a filter in the brew basket and pour the vinegar into the water reservoir. Run the brew cycle without coffee grounds. The vinegar will cleanse the system and remove any buildup. Rinse the system by running a brew cycle with just water. Your Keurig is now ready to use!Dec 1, 2023 · Next, lift the handle and lower after 5 seconds. 4. Press the brew button. The brew button should start flashing and the descale light will likely not turn off until the reset is complete. 5. You should’ve successfully reset the descale light. Observe if the descale light has reset and turned off. This can be fixed by repeating the descaling process until the light goes off. How to put a Keurig coffee maker in descale mode? Assuming you have a Keurig 2.0 Brewer, the process for putting it into descale mode is as follows: Press and hold the Brew Button for 3 seconds until the light on the display flashes.Place a large coffee mug or bowl on the drip tray. Turn the brewer off. Then press and hold the 8oz and 12oz buttons at the same time for 3 seconds until the light turns steady and does not flash. Shortly after step 5, the brew button will begin flashing. At that time, press the brew button to start the rinse.Blink Charging, an electric vehicle charger manufacturer, will be deploying EV chargers at General Motors dealerships across the U.S. and Canada, according to the company. The star...Follow the instructions below to reset the descale light and get your brewer back on track: Step 1: Unplug the Keurig Coffee Maker. Begin by unplugging the Keurig coffee maker from the power outlet. This ensures that the machine is completely powered down before we proceed with the reset process. Step 2: Remove and Clean the Water …Besides a Keurig coffee maker, the milk frothers are no less a blessing for coffee lovers. ... To turn off the flashing lights, identify the problem first. If the milk is insufficient, fill the jug to the minimum line. If you fill an adequate amount of milk but still face an issue, check if the frother is correctly connected to its base. ….

The Cuisinart Coffee Maker's clean light blinking indicates that the machine needs to be cleaned. You can start the self-cleaning cycle to clean the machine. Suppose the light doesn't turn off after the cleaning cycle. In that case, you can try running it again or taking it to an authorized Cuisinart service center.Take out whisk and clean it and the jug with warm soapy water and a non-abrasive sponge. If you regularly clean your frother, the issue could be with the whisk attachment. Make sure the black magnetic whisk piece is inside. Press down firmly on it before adding milk to the jug.Follow these steps to reset the light manually and turn off the descale indicator. Turn off Your Keurig Duo: Ensure that your Keurig Duo is powered off before proceeding with the reset process. Press the 8-Ounce and 10-Ounce Buttons Simultaneously: Locate the 8-ounce and 10-ounce buttons on your Keurig Duo.Flashing Blue — Fill the Cold Water Reservoir with cold water until it reaches just under the rim of the desired level – 6, 8, or 10 oz. of the Water Level Guide. Handle Indicator Flashing Blue — The blue light flashes when the minimum water amount of 6 oz. has been poured into the Cold Water Reservoir. After adding yourHow to fix the orange light blinking thrice per second? If you see a blinking orange light three times in one second, then the water flow is blocked. It is time to descale your machine. It will take almost 20 minutes to descale your Nespresso machine. However, this time is worth it. It will remove all the mineral buildup in the water.Descale your Keurig machine every 3 months. This will help clean out any limescale build-up inside your machine. You can descale your Keurig using Keurig cleaning solution or a mix of half water and half vinegar. Pour the solution into the reservoir and run several cycles without a K-cup until the reservoir is empty.I have purchased many Keurig coffee makers over the years ranging in price upto over $299.00 they all lasted about 2-5 years. I decided to just go simple and I purchased this at Walley World {Walmart} for about $49.00 5 or 6 years back I must say the K-Express {Red} has out performed the higher priced Keurig systems even though it is only ...A Keurig coffee maker's cup lights not working could indicate several issues, such as: 1. Power outage: If the coffee maker's lights stop working suddenly, it could be due to a power outage. Check if the power cord is securely plugged into an outlet and the power switch is turned on. 2. Faulty power supply cord: If the power cord is damaged ...Here are 10 simple steps that will help you reset the descale light on a Keurig coffee machine with the help of Keurig descaling solution. Step 1: Turn the machine off and unplug it from the power source. Step 2: Make sure to empty the water reservoir. Step 3: Detach the water filter present inside your water reservoir. Keurig coffee maker blinking lights, A Keurig coffee maker’s flashing lights might indicate several reasons. The following are some potential causes in specific Keurig models: K-Café (Flashing Frothier Light) K-Café is one of the two models that allow milk in a Keurig, which can sometimes cause trouble. The frothier light can blink for various reasons., A blinking projector screen is, at best, a minor annoyance, and, more often than not, a complete distraction that makes it hard for viewers to focus on the content of your presenta..., Keurig Blinking Light Cause. The cause of the blinking lights situation with a Keurig brewer is the machine unsure of its next step. This is usually the result of an interrupt to whatever it was working on. The interrupt could be from a power change, a break in a sensor signal, or just a bad day!, These coffee makers have a very tight lid that causes vacuum formation. The vacuum restricts the water from exiting the carafe. As a result, the next brew cycle will not complete, causing the coffee maker to shut down. ... If your Keurig is blinking red light and keeps shutting off afterward, it is a sign that the water reservoir requires draining., 1. How often should I descale my Keurig coffee maker? Keurig coffee makers should be descaled every three to six months, depending on the frequency of use and the hardness of the water. If you notice a decrease in the amount of coffee produced or if the coffee tastes weak or bitter, this may also be a sign that descaling is required. 2., Cuisinart - 12 Cup 2-In-1 Coffee Center Coffeemaker - Black Stainless Steel. User rating, 4.2 out of 5 stars with 169 reviews. (169) $199.99Your price for this item is $199.99. Keurig - K-Select Single-Serve K-Cup Pod Coffee Maker - Matte Black. User rating, 4.6 out of 5 stars with 4203 reviews. (4,203) $149.99Your price for this item is $149. ..., Blue Light Flashing. One of the most common lights you’ll see on a Keurig machine is blue light. This light is typically an alert that tells you that the water tank is very low or empty. To solve the problem with a blue flashing light, all you need to do is fill the water tank with fresh clean water., The most common issues with Keurig Coffee Makers are: The Display Isn't Working or Not Responding. Won't Heat Up Or Brew Coffee. Shuts Off On Its Own (When Idle Or Mid-Brew) The Machine Isn't Brewing The Correct Amount Of Coffee. Not to worry, though., But before that, remove the filter and filter holder. Place a large-sized cup so the solution can pour into the mug. Make sure your Keurig coffee maker is switched off. Now press the 8-ounce and 12-ounce buttons at the same time - hold down on them for 3 seconds. Then hit the K button to begin the descaling process., It can be frustrating when your Keurig lights are not blinking as they should, but with a few simple steps, you may get your coffee maker back up and strolling smoothly. 1. Check the power source: Ensure that your Keurig coffee maker is properly plugged into a functioning power outlet. Sometimes, a loose connection or power surge can cause the ..., There are four ways to reset the clean light. Firstly, unplug your Mr. Coffee maker from the power source. Then, press and hold the "Restore" button. Hold the "Restore" button while plugging in the machine back. Lastly, wait for ten seconds before releasing the "Restore" button., However, you might have noticed that the Keurig coffee maker doesn’t have a reset button. Instead, here are your options: Open and close the K-Cup lever. This should reset it back to being “ready to brew.” Turn off your Keurig coffee machine and unplug it from the wall. Let it rest for a few hours before plugging it back in., Turn the brewer off. Then press and hold the 8oz and 12oz buttons at the same time for 3 seconds until the light turns steady and does not flash. Shortly after step 5, the brew button will begin flashing. At that time, press the brew button to start the rinse. Repeat step 6 until the ADD WATER indicator light turns on., iFixit. Repair guides and support for coffee makers by Keurig including the K-Cup systems. Keurig Coffee Maker troubleshooting, repair, and service manuals., The issue may be with the coffee maker itself if the coffee maker is plugged in and the water reservoir is filled. The light is flashing and there’s no coffee brewing, unplug the coffee maker and contact Keurig customer service for further troubleshooting. Keurig K-Slim Descale Light Stays On , The lights flicker when the coffee maker is in use because something may be wrong with your home's electrical system. A light bulb might be loose. There might be a loose connection in the outlet, or you are using the wrong light bulb. Also, an electrical overload could be the reason because of drawing too much current that causes the light to ..., Keurig Milk Frother Problems. Keurig is one of the world’s leading brands that makes the best performing kitchen appliances on the market. The Keurig brand has a variety of appliances that are exceptionally good in terms of quality, durability and features. That’s why you may want a Keurig milk frother to make delectable beverages. Whether ..., 2 Guide To Fix Keurig Won't Power On Issue. 2.1 Power Cord is not Plugged in Properly or is Loose. 2.2 Power Outlet is not Functioning Properly. 2.3 Circuit Breaker or Fuse has Tripped. 2.4 Water Reservoir is not Seated Properly. 2.5 Keurig Machine is in Need of Descaling. 2.6 Defective or Damaged Internal Components., Resetting and restarting the Keurig. Perform a power cycle reset: Disconnect the power cord from the electrical outlet and wait for approximately one minute. Reconnect the power cord and power on the Keurig machine to see if it resolves the issue. Factory reset or system reboot options: Consult your Keurig machine’s user manual or online ..., Amazon customers can also recycle their old cameras by requesting a free UPS shipping label through the Amazon Recycling Progam. Amazon is now offering to replace customers’ discon..., Toll-free, 7 days a week. Live Chat. Connect with Keurig representative. Email Us Your Questions. Find a Store. Customer Support: 866-901-2739. Shop. Coffee Makers. Beverages., To do this, turn off the machine and unplug it from the power source. Remove the water reservoir and empty any water that may be inside. Press and hold the power button for 5-10 seconds. After that, release the button and plug the machine back in. Turn it on and check if the lights are functioning properly., The Keurig latte maker is a popular coffee maker that uses pods. The pods are inserted into the machine, and hot water is heated up and forced through the coffee pod to make a fresh cup of coffee. The Keurig latte maker is easy to use, and most people find it to be very convenient. The Keurig latte maker is very easy to use., Clear Possible Air Lock. Air can get trapped in the water line, causing the "ADD WATER" light to stay on. To clear any airlocks, remove the water tank, turn the brewer off, tilt it upside down for a few seconds, and then return it to the upright position. Reinsert the water tank and see if the issue is resolved., The Keurig K-Express Essentials is a coffee maker that offers a convenient and hassle-free brewing experience. Designed for simplicity, it allows users to make a single cup of coffee quickly and easily. The machine features a compact design, making it suitable for small kitchens or limited counter space. Equipped with a single-serve system, the ..., Contents show 1 Why are All the Lights on Keurig Coffee Maker Illuminated? 2 Quick Fixes for Keurig All Lights on 2.1 Check the Power Source and How It's Connected 2.2 Turn the Keurig Machine Back on 2.3 Check and Change the Location of the Water Reservoir 2.4 Make Sure There's Enough Water 2.5 Check […], Blue lights wouldn’t come on. I hit the glass pot button like 20+ times. Turned it on and off and pressed the glass pot button again and the blue lights came on like normal and now I can brew with my glass pot again. Note: I have the double brew station. One for a pot and the other for a cup. I cleaned it with the Keurig Descale Solution and ..., Keurig 3-Month Brewer Maintenance Kit Includes Descaling Solution, Water Filter Cartridges & Rinse Pods, Compatible Classic/1.0 & 2.0 K-Cup Coffee Makers, 7 Count INCLUDES: 4 Keurig Rinse Pods, 1 Descale Solution, and 2 Water Filter Cartridge Refills, Step 2: Is the power icon displayed on the bottom right of the screen? Yes: Continue to step 3. No: Please see Troubleshooting Tip: My Brewer Isn't Powering On. Step 3: Go into the Menu and try to set the clock. Step 4: Proceed through the menu and try to set all your menu options. Step 5: When the LCD is navigated back to the "Lift to ..., Keurig coffee maker is a pretty reliable partner for the morning routine (read: coffee cup), but don’t be surprised if you face some problems. Different kinds of lights flashing or a non-responding …, The coffee maker will only brew a partially filled cup. ... All Indication Lights Are On And Flashing. After turning the device on, the indicator lights begin to flash on and off. Filled or Dirty Water Reservoir. ... My Keurig is turned on. Their is a circle light on the bottom right. The cup is fit securely and water is filled., 1 Cup and 2 Cup Lights Flashing At The Same Time. When both the 1 Cup and 2 Cup light are flashing red, it means that your De'Longhi machine is not yet ready to make coffee. This is usually because you have not given it enough time for the water to reach the ideal temperature. It generally takes about 45 seconds for the machine to warm up., A safe place to talk about the Keurig K-Cup Coffee system. ... Automatic Tea Maker with Coffee Machine ... I've had this light for 5+ years and it's been through all kinds of shenanigans - submersed in hot CIP chemicals for hours and came out with the light still on. Impressive! It's made by Hictech. Any help appreciated!