Kwikset smart lock beeping after battery change

SmartKey® re-key technology is compatible with Kwikset (KW1) keyway. Patented Bump proof and Pick resistant side locking bar technology. Installs in minutes with just a screw driver no hard wiring needed. Fits standard doors (1-3/8in. – 2in.) no new screw holes required. Tamper resistant interior.

To factory reset Kwikset 913: Remove the battery pack. Press and HOLD the Program button while reinserting the battery pack. Hold the button for 30 seconds until the lock beeps and the Status LED flashes red. Press the Program button once more. The lock has been reset when the LED flashes green, and you hear one beep.Step 3: Replace the Old Batteries. Carefully remove the old batteries from the battery compartment. In the case of the Kwikset Halo Smart Lock, you will need four new AA batteries. Pay close attention to the correct polarity while inserting the new batteries. The negative polarity of the battery will touch the spring in the case. Remove the cover and the battery. Hold and press the program for about 5-7 seconds. Next, press and hold the A button for about 5 seconds (This button may be black and located on the assembly inside your lock) Replace the batteries with new ones, make sure they’re in place, and close the lids. Replace with the new tapered latch that came with the lock and reinstall the lock. The deadbolt latch and strike are misaligned, causing the latch to bind. Adjust the tab of the lower strike (for your knob or lever) to help align the upper latch and strike so that the latch bolt enters the strike when the door is locked.When I hit the lock button, everything blinked red rapidly for a couple seconds. That's the indicator that it's time for a new battery. Here's how! ... That's the indicator that it's time for a ...1 = Door lock status LED blinks every 6 seconds. 2 = Lock automatically re-locks door 30 seconds after unlocking. 3 = Audio. 4 = Not used. LED Color: Blinking green = Unlocked. Blinking amber = Locked. Blinking red = Low battery. Solid red = Door handing process did not work properly.Disassemble the lock, and reinstall it without the adapter ring on the exterior side of the door. The latch is installed upside down. See page 8. The battery level is too low. This is indicated by the keypad fl ashing red three times with three beeps. Use a fresh set of batteries, and perform the door handing process again.

First, locate the reset button located near the bottom of your Kwikset lock. Press and hold this button for about 10 seconds until you hear two quick beeps indicating that it has been reset successfully. Next, enter your desired new code into the keypad followed by pressing "#" to confirm it.Control from anywhere. With the Kwikset app and your smartphone, you can manage your lock from anywhere. Lock and unlock, manage user codes, view lock activity, receive lock notifications and much more. Your existing Wi-Fi router and an internet connection brings the ultimate in security and convenience right to your fingertips.2. Issue: Won't connect to the smart home system. If you can't successfully connect the smart lock to your smart home system, it's probably a pairing issue. Firstly, check if your smart home system is connected to other smart locks - maybe an old unit you have - then unpair it. After that, try connecting your Kwikset again.Enter a new PC. It must be between 4 and 10 digits.4. Press "Kwikset"For all programming sequences, success is indicated when the Kwikset button flashes green 2 times and you hear 2 beeps.If unsuccessful, the Kwikset button will flash red 3 times and you will hear 3 beeps.Note: If the lock is muted, you will not hear the lock beeping. Read MoreHowever, misaligned doors where the lock faces resistance during lock/unlocking will shorten the battery life since the motor uses more power to exercise the latch. In addition, properly “handing” or calibrating the lock as outlined in the installation guide will maximize the battery life. Refer to the step 5 in the installation instructions.

1. If using a smart device, hold the smart device close to the Kevo deadbolt and touch the lock. If your smart device doesn't vibrate, and the Bluetooth symbol (located at the top of your screen) doesn't flash, this is an indication that there is no Bluetooth communication. Make sure the app is open (either in background or foreground) and you ...A "future proof" Universal Enhanced Z-Wave Lock driver This driver is enhanced to fix bugs in the stock ST ZWave Lock driver, include patches for bugs in lock firmwares and bring out additional features for Schalge, Yale, Kwikset, IDLock, Popp, Samsung, Delaney, August Pro, Danalock, KeyWe, Philia, Vivint, Locstar etc zwave locks (see below for a full list of models and features). This ...On my Smartcode Deadbolt, Keypad flashes red three times with three beeps* (beeping sound will only be heard if switch #3 is on) Three possible reasons: 1. No user code programmed. Program at least one user code. 2. Programming timeout after five seconds. Attempt programming procedure again. 3. Unsuccessful programming.Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.3. Press the Program button once more. When the LED flashes green and you hear two beeps, the lock has been reset.4. IF A SMART LOCK PRODUCT: Pair the lock with your smart home system5.1. Duracell - CopperTop AA Alkaline Batteries. Duracell CopperTop AA alkaline batteries are a perfect match for your Kwikset lock. They provide reliable and long-lasting power to keep your lock functioning smoothly. With a shelf life of up to 10 years, these batteries are ideal for long-term storage and emergency use.

The holdovers showtimes near old mill playhouse.

Jul 25, 2021 · If you replaced the batteries on your Kwikset lock after getting a low battery warning, chances are the lock may not work almost immediately. If this is the case with your lock, here is what you need to do: Remove the battery pack from the lock. Press and hold the Program button for about 5 seconds. Here is how you can reset your Kwikset Halo lock: Step 1: Begin by removing the batteries from the lock. You will be able to do that by removing the screws on the sides of the interior assembly. Step 2: Once the batteries are removed, press and hold the program button. Here is where you will find the program button.Remove interior cover and battery pack. Press and HOLD the Lock button while installing battery pack. Hold button until the latch bolt starts moving on its own. Did the latch bolt retract and extend on its own when the battery pack was installed? Note: Latch bolt will only retract half way.Page 3 Install interior assembly Remove the battery cover. Load 4 AA batteries into the interior Press and hold the Reset button on the interior assembly. For best results, use new, non- assembly for 5 seconds, until you hear 3 long beeps. rechargeable Alkaline batteries only. Page 4: Troubleshooting Quick Setup and Use Move swiftly during ...Follow the provided instructions to change the Master Code on a defiant lock: Press down and hold the SET button and wait until the lock beeps and then set it free. Now enter your present Master Code and then press the Lock button. (For a new Defiant lock, use your default Master Code—123456). Again press 1, 0, and then the Lock button.

Smart Locks Basics. Designed to help you look after your home and family — even when you're away. Compare Smart Locks. Works With. App. Aura. Halo. Obsidian. Premis. Halo Touch . Browse Smart Locks. View and compare all smart locks. Innovation. The Kwikset Home. Security on the outside, convenience on the inside. Explore a world of ...In the case of the Z-Wave SmartCode 910, you start by initiating the process to add the lock from your smart home controller. When prompted, press button “A” on the lock's interior once, and the red LED should light up as it enters Add Mode. If it's successful, rename the lock within your system.6. Replace Kwikset Lock Or Contact Support. If you have checked the position of the new batteries, did a reset, checked for damage, and tried all of the other small fixes, and it still won't won't after the battery change, it's time to either replace your Kwikset lock. I personally use the Kwikset Halo, which I picked up from Amazon.The SmartCode is reversible and can be installed on both left and right hand doors. (1) Hold LOCK button on keypad while (2) inserting the battery pack into the interior. The lock will automatically sense the handing of the door and will extend & retract deadbolt latch.Yes, a kit (83159) is available to install Home Connect 620 locks on doors with a thickness between 2" (51mm) and. 2-1/4" (57mm). Call our support center at. 1-800-327-5625. to order a thick door kit. Home Connect 620 locks are compatible with 1-1/2" (38mm) and 2-1/8" (54mm) door holes. Please refer to the.Audible beep and visual flash when batteries are low power; ... Backlit, Delay Timer, Fail-Safe, Kwikset SmartKey, Low Battery Indicator Light, Rekeyable. Adjustable Backset, Automatic Relocking, Delay Timer, Easy Installation, Fail-Safe, Kwikset SmartKey, Rekeyable ... Aura Bluetooth Smart Lock is a keyless entry electronic deadbolt featuring ...For iPhone: Step 1: Open "Settings" on your iPhone. Step 2: Access the "Bluetooth" settings. Make sure Bluetooth is enabled. Step 3: In the list of paired devices, find the Kwikset App. Tap the info icon (typically an "i" in a circle) next to the Kwikset App. Step 4: Select the option to "Forget This Device.".Disassemble the lock, and reinstall it without the adapter ring on the exterior side of the door. The latch is installed upside down. See page 8. The battery level is too low. This is indicated by the keypad fl ashing red three times with three beeps. Use a fresh set of batteries, and perform the door handing process again.1. If using a smart device, hold the smart device close to the Kevo deadbolt and touch the lock. If your smart device doesn't vibrate, and the Bluetooth symbol (located at the top of your screen) doesn't flash, this is an indication that there is no Bluetooth communication. Make sure the app is open (either in background or foreground) and you ...Step-by-step instructions for programming the loc k. Follow these simple steps to program your Kwikset Smartcode 260: Start by ensuring the door is open and unlocked. Locate the programming button on the interior part of the lock. Press and hold the programming button for around 5 seconds until the keypad flashes.

A network reset on the Halo Smart Locks deletes Wi-Fi settings, Bluetooth settings, user info, and will remove the lock from the account. Here are the steps for performing a network reset on a Kwikset Halo Smart Lock: 1. Press and hold the "A" button for 10 seconds until you hear 1 beep and see an amber LED. 2.

2. The smart home system controller's communication with the lock is draining the battery. Remove the lock from your system. Put a new set of batteries in the lock. Operate the lock in stand-alone mode for a week. If the batteries drain within the week, the problem resides in the lock. If the batteries do not drain, the problem may be the ...A green light means it is unlocked. An amber or orange-colored light means it is locked. A red light means the device has a low battery. IMPORTANT: If your lock is flashing red, we recommend changing the batteries as soon as possible. If the batteries die completely, you will not be able to unlock the door using your keypad outside or via the ...Enter your existing PC (Programming Code). 2. Press "Kwikset" then "4" then "Kwikset". 3. Enter a new PC. It must be between 4 and 10 digits. 4. Press "Kwikset". For all programming sequences, success is indicated when the Kwikset button flashes green 2 times and you hear 2 beeps.When I hit the lock button, everything blinked red rapidly for a couple seconds. That's the indicator that it's time for a new battery. Here's how! ... That's the indicator that it's time for a ...Step 3: Install the Exterior Part of the Smart Lock. Starting from outside the door, place the exterior part of the smart lock over the hole and feed the cable underneath the latch. Insert the turn rod through the middle hole of the latch, making sure to align its "D" shape with the latch.Smart Locks Basics. ... Premis. Halo Touch . Browse Smart Locks. View and compare all smart locks. Innovation. The Kwikset Home. Security on the outside, convenience on the inside. Explore a world of innovations. Life Experiences ... Amber indicates locked. Green indicates unlocked. Red indicates low battery. For other operating modes, Please ...How to Replace The Batteries In Kevo Smart Lock? Remove interior screws. Turnpiece must be vertical. Slide to remove the interior cover. Remove the battery pack. Replace the batteries. Install battery pack. Reinstall interior screws.The Deadbolt Does Not Lock The Door And Kevo Convert Beeps/Lights Up Red. This is a 'bolt jam' alert. It means that Kevo Convert was unable to extend the deadbolt and your door was not locked. This happens when the door was not shut properly and the deadbolt could not fully extend into the strike hole. Make sure the door is shut properly to ...1. Duracell - CopperTop AA Alkaline Batteries. Duracell CopperTop AA alkaline batteries are a perfect match for your Kwikset lock. They provide reliable and long-lasting power to keep your lock functioning smoothly. With a shelf life of up to 10 years, these batteries are ideal for long-term storage and emergency use.Feb 1, 2023 · Troubleshoot a Schlage Lock that Won’t Work After Replacing Batteries. Troubleshoot Brinks Digital Deadbolt. Program Garrison Electronic Deadbolt. If your Kwikset Lock refuses to power up after replacing the batteries, here are some tips to help you get your lock up and running again.

Gotrax brake pads.

Anoxic brain injury nursing diagnosis.

In recent years, there has been a growing interest in sustainable energy solutions for residential properties. One such solution that has gained significant popularity is the Tesla...How to Factory Reset a Kwikset 910: Remove the battery pack from the lock. Reinsert the battery pack while holding the Program button on the lock. Continue holding the Program button for 30 seconds until the lock beeps and the status LED begins to flash red. After a few seconds, the door will initiate the handing sequence to signal a successful ...Door Handing is the process by which the Kevo Smart Lock determines whether the deadbolt faces the right or the left. Door handing instructions: 1. Remove the battery cover. 2. Remove the battery pack from the lock. 3. While holding the Program button, reinsert the battery pack, then release the Program button. 4.Inserting the New Batteries. To change the batteries in a Kwikset door lock, locate the battery cover on the interior side of the lock, remove the cover, and replace the old batteries with new ones. Make sure to follow the correct polarity (+/-) when inserting the new batteries.Hi, this is MeetBrandon. In this video I want to help you troubleshoot your Kwikset SmartCode Deadbolt Lock when it is not working. In the next video I chang...Kwikset button is pushed after entering the User Code. If the door still won't unlock, use a key to unlock the door. Call technical support for further troubleshooting. When the door is closed and the Kwikset button is pressed to lock the door, the lock beeps 3 times. When the door is open and the Kwikset button is pressed to lock the door,Manage your Aura Smart Lock from your phone when you are within Bluetooth range. Lock and unlock the door, add or remove users, control access and monitor usage - all from your smart phone. ... The Kwikset app's Lock Activity screen conveniently displays all of Aura's activity including actions such as locking, ... Accessible Battery ...Smart Locks Basics. ... If you hear three beeps andNote: The lock will time out after five seconds.Disabling and Deleting the Mastercode1. Keep door open. Press and HOLD the Program button until the keypad Flashes green (about 5 seconds).2. Press Lock button once.3. ... Replace the battery pack. If the Wireless Card LEDs continue to stay on ...To perform a reset, first, take out the battery pack from the lock. Then, press and hold the Program button while you reinsert the battery pack into the lock. Be sure to keep holding the Program button for a full 30 seconds, until you hear the lock beep and see the status LED flash red.SmartKey Security™ re-key technology is compatible with Kwikset (KW1) keyway. Comes with 2 keys. Latch is 20 minute fire rated with round corner face. ANSI/BHMA grade 2 certified. Latch has adjustable backset 2-3/8" to 2-3/4" to fit all standard door preparations. Includes round deadbolt strike.2. Keep the button pressed for at least 30 seconds until you see the lock's LED lights flash three times. 3. Once the reset is complete, you can reprogram with your default programming code. As not every Schlage lock is reset the same way, refer to your Schlage lock resetting guide for help with different models. 5. ….

The Kwikset app's Lock Activity screen conveniently displays all of Halo's activity including actions such as locking, unlocking, low battery warning, manual key-based entries, and other alerts. ... Low Battery Alerts. Audible beeps and visual flash when batteries are low. 20 Minute Fire Rating. ... Halo Touchscreen Smart Deadbolt | Halo Wi ...Locate the program button, rotate the battery handle, and remove the battery. Step 3: Press hold on the button and inside the battery back. Step 4: In case of a Kwikset 917 and 955 you will need to use a paper clip or a pin to access the program button. Step 5: Wait for 20 to 30 seconds until you hear a beep or two.Jan 30, 2015 · If it is after lock, you could reset the bolt by holding down the lock key while reinserting the batteries. I honestly can’t remember. It may be on unlock only. I’ll try replacing the batteries and let you both know. 1 Like. Todd_Whitehead (Todd Whitehead) January 30, 2015, 10:02pm 5. Mine does that when the battery needs to be replaced. Click here to start protecting your home with award-winning home security today: https://bit.ly/2W2mKC2Protect America is an award-winning DIY home security ...Press and hold the “Program” button while reinserting the battery pack. The lock will beep and the status LED will flash red and green. If you are having issue with the beeping read this troubleshooting for kwikset beeping issue. Release the “Program” button when the LED flashes green. 4.6:.6. Replace Kwikset Lock Or Contact Support. If you have checked the position of the new batteries, did a reset, checked for damage, and tried all of the other small fixes, and it still won’t won’t after the battery change, it’s time to either replace your Kwikset lock. I personally use the Kwikset Halo, which I picked up from Amazon.May 30, 2023 · 6. Replace Kwikset Lock Or Contact Support. If you have checked the position of the new batteries, did a reset, checked for damage, and tried all of the other small fixes, and it still won’t won’t after the battery change, it’s time to either replace your Kwikset lock. I personally use the Kwikset Halo, which I picked up from Amazon. If the 4 AA batteries are too low to operate the lock, use a 9-Volt Alkaline battery to temporarily power the lock. Make sure both terminals on the 9-Volt battery touch the terminals below the keypad. When lock has enough power you will hear 3 short beeps. Hold the 9-Volt in place while entering your user code to unlock the door. Kwikset smart lock beeping after battery change, Extended wireless range and superior 128-bit wireless encryption. Up to 30 user access codes for family and guests to use at the door. Secured keyless entry convenience. One touch locking. Dramatically reduced interior size and sleek metal design. 30 user codes plus master code feature for added security. 5 digit keypad with dedicated lock button., Program at least one user code and test the Lock button again. The battery is too low to lock the door. This is indicated by the keypad flashing red three times with three beeps. Remove the batteries and replace with a fresh set. The set screw in the lever was not fully tightened. Fully tighten the pre-installed set screw at the bottom of the ..., You’ll need to program your lock again after performing a factory reset. Here’s how to reset your Kwikset SmartCode 913: Remove the battery cover. Next, remove the battery pack. Press and hold the Program button (a black circle button on the inside of the interior assembly) Replace the battery pack while still holding the Program button., Many modern car alarms are sophisticated components that tie into the vehicle's ECU (main computer) as well as the ignition system. While cheap, no-name, generic or off-brand alarm..., A network reset on the Halo Smart Locks deletes Wi-Fi settings, Bluetooth settings, user info, and will remove the lock from the account. Here are the steps for performing a network reset on a Kwikset Halo Smart Lock: 1. Press and hold the "A" button for 10 seconds until you hear 1 beep and see an amber LED. 2., Identifying Your Kwikset Smart Lock Model. Before you change the batteries in your Kwikset smart lock, it is essential to identify the specific model you are using. Kwikset offers several smart lock models that come in a variety of styles and have different battery replacement procedures. Some of the popular Kwikset smart lock …, Ultimate control. Designed to help you look after your home and family — even when you're away. No key required. Control locks from anywhere. Smart Home Integration., First, locate the reset button located near the bottom of your Kwikset lock. Press and hold this button for about 10 seconds until you hear two quick beeps indicating that it has been reset successfully. Next, enter your desired new code into the keypad followed by pressing "#" to confirm it., The steps below are to change your access code to a new code. This will also remove any previous codes stored in the Powerbolt's memory.1. Manually put the bolt in the extended (lock) position. Press the PROGRAM button once, enter your new 4 - 8 digit code and then press the LOCK button.2. Press the PROGRAM button twice, enter the same or a new ..., Kwikset Lock Not Working After Battery Change Solution. This article covers proven solution to fix the battery change issues in Kwikset Lock., The lock should beep twice when it unlocks and once when it locks. It will also beep if there is a warning such as a low battery or a jammed bolt. To turn the beeping sound off: 1. Remove the battery cover. 2. Move the third switch from the left (it has a speaker icon above it) to the OFF (downward) position. 3., See Kwikset smart locks that work with smart phone products and your smart phone. SecureScreen™ Technology. Touchscreen Security . Patented technology to help prevent code detection from fingerprints on the touchscreen. Available in touchscreen electronic locks and smart locks., Smart Locks Basics. Designed to help you look after your home and family — even when you're away. Compare Smart Locks. Works With. App. Aura. Halo. Obsidian. Premis. Halo Touch . Browse Smart Locks. View and compare all smart locks. Innovation. The Kwikset Home. Security on the outside, convenience on the inside. Explore a world of ..., Factory Reset should be used when you want to change the lock owner, have lost your phone, or are troubleshooting a new installation. Before you begin the Factory Reset process: Delete the lock from the home within the Kwikset app, and remove the lock from your phone's Bluetooth list by tapping Forget Device in Bluetooth settings. Factory Reset., Hi, this is MeetBrandon. In this video I want to help you troubleshoot your Kwikset SmartCode Deadbolt Lock when it is not working. In the next video I chang..., To utilize this option, do the following: Locate the emergency power port on the lock. Connect a 9V battery to the port. Once connected, the LED will emit a red light, indicating that the lock is receiving power. Quickly enter your access code on the keypad to unlock the door., This is the procedure for resetting the Kwikset 916 lock code: Press and hold the program button. Wait for the checkmark symbol to illuminate. Press the checkmark symbol once. Enter the new lock code/master code. Press Lock. Re-enter the new lock code/master code. Press Lock., Smart Locks Basics. ... Remove battery pack. 3. Replace batteries. Connect with us. ... Sign up for Kwikset updates to stay informed about new products, promotions ..., 2. The smart home system controller's communication with the lock is draining the battery. Remove the lock from your system. Put a new set of batteries in the lock. Operate the lock in stand-alone mode for a week. If the batteries drain within the week, the problem resides in the lock. If the batteries do not drain, the problem may be the ..., To perform a reset, first, take out the battery pack from the lock. Then, press and hold the Program button while you reinsert the battery pack into the lock. Be sure to keep holding the Program button for a full 30 seconds, until you hear the lock beep and see the status LED flash red., While you're at it, take it as an opportunity to replace your smart lock batteries if needed. Kwikset smart locks use 2 AA batteries. So, make sure to get the same type of battery. Plus, ensure that they're correctly inserted. You might also want to know: 5 Steps to Change the Batteries in an August Smart Lock #4: Press and hold the program ..., The Halo deadbolt can be locked using the Kwikset app. From the outside, Halo has a convenient 1-touch locking button on the keypad to easily lock the deadbolt or with a key. From the inside, Halo can be locked using the sleek turnpiece. Additionally, the lock features Auto Lock which will automatically lock after a preset time delay., Smart Locks Basics. ... If you hear three beeps andNote: The lock will time out after five seconds.Disabling and Deleting the Mastercode1. Keep door open. Press and HOLD the Program button until the keypad Flashes green (about 5 seconds).2. Press Lock button once.3. ... Replace the battery pack. If the Wireless Card LEDs continue to stay on ..., If the 4 AA batteries are too low to operate the lock, use a 9-Volt Alkaline battery to temporarily power the lock. Make sure both terminals on the 9-Volt battery touch the terminals below the keypad. When lock has enough power you will hear 3 short beeps. Hold the 9-Volt in place while entering your user code to unlock the door., Make sure the lock is unlocked and the door is open.2. Enter your existing Mastercode.3. Press the lock button. You will hear one beep.4. Press 1 - 9.5. Press the lock button. You will hear one beep.6. Enter a new User Code. It must be 4-10 digits.7. Press the lock button. You will hear two beeps if successful. If you hear three beeps, it was ..., Press Lock button once7. Press "9" six times.8. Press Lock button once.If programming is successful, the keypad will flash green once with one beep.If programming is unsuccessful, the keypad will fl ash red three times with three beeps. Make sure to enter a valid Mastercode in step 3 during your next attempt9., If your Kwikset smart lock keeps beeping after changing the batteries, remove the cover, unscrew the interior, and unplug the power cable. Leave the lock powered off like that for 5 to 15 minutes. When ready, connect the cables, secure the lock to the door, and insert the batteries back in. , Insert the wrench that came with your lock into a screw, which should be on the left side of the battery cover. If you cannot find the screws, consult the user manual. Repeat Step 3 for the right side and bottom screws of the battery cover. Remove the battery cover and pull the battery pack out of the lock., Reset your lock to original settings. Make sure the lock is in the unlocked position. Remove the battery cover. Press and hold the “Reset” button for 5 seconds. You will hear 3 long beeps after the 5 seconds is completed indicating the lock has been reset. You will reset your User Code to 1-2-3-4 and Mastercode to 0-0-0-0 when the reset is ..., If you hear 1 short beeps and 1 long red flash, it means that the lock auto locks. If you hear 2 short beeps, it means that the turnpiece rotated to unlock position. If you hear 1 long beep, it means that the turnpiece rotated to locked position. If you hear 10 short beeps and 10 short red flashes, it means low battery., The lock should beep twice when it unlocks and once when it locks. It will also beep if there is a warning such as a low battery or a jammed bolt. To turn the beeping sound off: 1. Remove the battery cover. 2. Move the third switch from the left (it has a speaker icon above it) to the OFF (downward) position. 3., If your Vivint door lock is not locking or unlocking, check the following: Check for low batteries. If the red light on the back of your door lock is blinking or if you have a low battery alert on your touchscreen panel, you'll need to replace your batteries with four new AA batteries. Smart Lock (892) - Change Batteries., May 26, 2023 · Step 4: Resetting Your Lock. If your Kwikset lock continues to beep after replacing your batteries or clearing a jammed bolt, you may need to reset Kwikset smart lock. To reset your lock, follow these steps: Step 1: Remove the interior cover of your Kwikset lock. Step 2: Press and hold the lock button for 30 seconds.